Der er 91 varer.
RC Project Kit Shock Pins with thread in Ergal 7075-T6 (4)
The Shock Pins "Valente Edition" are Made in Italy, with latest generation Swiss type lathe center. Our products are made with Ergal 7075-T6 billet and then Hard Coating with a thickness of 50µ. The "Valente Edition" pins have the 5.5mm External Hexagon and a 2.5mm Internal Hex to be screwed with the Screwdriver. The Black pins have the right-hand thread and the Gold pins have the left-hand thread. The Diameter of the Thread has been increased by 0.05mm to be able to adapt even to non-new arms. The weight of the Kit is 3.5g.
RC Project Kit Standoff Shockabsorbers +5mm in Ergal 7075-T6 (2)
The New Standoff are produced from a bar in Ergal 7075 T6 Certificate, unlike all the Standoff currently on the market we have studied a particular Geometry that allows to increase the Contact Surface between Bushing and Standoff; this allows a life of the Standoff and the relative Bushing of 600% more than the whole Competition. To finish a Hard Coating and Teflon Treatment allows to reduce the friction between Bushing and Standoff, all this has allowed us to Guarantee 30/35 Liters without replacing Standoff and Bushing . To decrease the suspended masses and improve driveability, you will also find the corresponding Titanium Grade 5 6Al4V Allen Screw with Rolled Thread. Replacing Articles SW330138B.
RC Project Kit Upper Link Balls "REVERSE" in Ergal 7075-T6 (2)
The Balls are Made in Italy, with latest generation Swiss type lathe center. Our products are made with Ergal 7075-T6 billet and then Hard Coating with a thickness of 50µ. In addition, a Teflon Coating was carried out to reduce the coefficient of friction with the Uniball. The weight of the Kit is 2.0g.
RC Project Kit Steering Balls for Ackerman Alu T7075-T6 (4)
The Balls are Made in Italy, with latest generation Swiss type lathe center. Our products are made with Ergal 7075-T6 billet and then Hard Coating with a thickness of 50µ. In addition, a Teflon Coating was carried out to reduce the coefficient of friction with the Uniball. The weight of the Kit is 2.0g.
SWORKz Plastic Center Big Bore HET Diff Case (Hard)
SWORKz Plastic Front/Rear Big Bore HET Diff Case Hard
SWORKz S35 Shock Conversion Kit V2(4)
Set consisting of 4 shock absorbers specially adapted for the SWORKz S35 vehicles from our partner Fast Race. The set includes 4 membranes of different hardness to adapt the damping to different routes. Yellow = soft, blue = medium, orange = hard
SWORKz Colourful Plastic Inserts Set RED (2Set)
SWORKz Front Lower Arm in Hard Material (1PC)
SWORKz Rear Lower Arm in Hard Material (1PC)
SWORKz Front Lower Arm in Medium Material (1PC)
SWORKz Rear Lower Arm in Medium Material (1PC)
SWORKz 1/8 Off Road Pro-Speed 2.0 Race Wing (BLACK)(Pre-Holes)
SWORKz 1/8 Off Road Pro-Speed 2.0 Race Wing (WHITE)(Pre-Holes)
SWORKz 1/8 BBS Precision Plastic Shock Piston(DIY)(4)
SWORKz 1/8 Off Road Pro Race Wing (BK)(W/o Holes)
SWORKz 1/8 Off Road Pro Race Wing (FY)(W/o Holes)
SWORKz 1/8 Off Road Pro Race Wing (WH)(W/o Holes)
SWORKz 1/8 Off Road Formula Front Upper Arms Lexan Wing (0.8mm)(4PC)
SWORKz 1/8 Series Shock Cap Insert (8pc)
SWORKz Front Upper Arms Hard (2pc)
SWORKz Rear Chassis Blance wight 15g(2pc)
SWORKz S350 Series Pro Wheel Nut (GM) (4)
SWORKz S350 Series Knuckle Pivot Ball Balance Nut (5.5g)
SWORKz S350 Series Aluminum Wing Holder Red (2)
SWORKz S350/S350T Series Aluminum Wing Holder (BK) (2)
SWORKz S350/S350T Series Aluminum Wing Holder (GM) (2)
SWORKz Lightend Wheel Hub 6.5mm for 8mm Axle (2)
SWORKz BBS System Shock Spring Adjust Nut (RED)(2PC)
SWORKz Aluminum Steering Linkage Ball Stud 7mm(L7)(4PC)
SWORKz Drive Shaft 3x12.8mm Pin for replacement (10)
SWORKz Lightened Aluminum Rear Chassis Brace
The all new design S35-3 Series Lightened Aluminum Front and Rear Chassis Brace are made of high quality T7075 aluminum.
SWORKz Center HET Spur Gear (46T)
SWORKz Center HET Spur Gear (48T)
SWORKz Brass Reinforcement for Center Chassis (50g)
SWORKz Rear Upper Arm Aluminum Ball Stud(2PC)
SWORKz T7 Aluminium Rear Wheel Hub (1)
SWORKz Uni-Design 2-Way System Aluminium Steering Servo Horn 25T
SWORKz S35-4E Series Aluminum Steering Servo Mount
The standard S35-4E servo mount is made of plastic. Now there is a new option made from CNC machined high-strength aluminum. It is hard-coated on the outside. The new servo mount ensures a more exact and precise steering response.